※上記の広告は60日以上更新のないWIKIに表示されています。更新することで広告が下部へ移動します。

起動メッセージ

  1. シリアルコンソール使用
  2. LAN接続済み
  3. HDD装着
Orion1   CPU =  Low 

=== KURO U-Boot. ===
 ** LOADER **
 ** KUROBOX BOARD: KURO_BOX  LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY

DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB 
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz 
Orion 1 streaming disabled 
SysClock = 250Mhz , TClock = 166Mhz 


USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
hit any key to switch tftp boot.
Hit any key to stop autoboot:  2  1  0 
<<system_bootend>>
Hit any key to stop autoboot:  3  2  1  0 

Reset IDE: 
Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: ST380815AS                               Firm: 3.AAC    Ser#:             9QZ15T5J
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1736436 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2007-02-08   6:00:09 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1736372 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_KUROBOX ---

Uncompressing Linux................................................................................................................. done, booting the kernel.

Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #2 Thu Feb 8 15:00:20 JST 2007

CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 425K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
 config_device_cs Error : Unknown board 


CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB 
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
PCI0_MEM ....base e8000000, size 128MB 
PCI0_IO ....base f2100000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
DEVICE_CS0 ....base fa000000, size   2MB 
DEVICE_CS1 ....base f4000000, size  32MB 
DEVICE_CS2 ....base fa800000, size   1MB 
DEV_BOOCS ....base ff800000, size   8MB 
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
BUFFALO KUROBOX FLASH size 4096[KB]


  Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- BUFFALO_BOARD_KUROBOX  Soc: 88F5182 A2


 Detected Tclk 166664740 and SysClk 250000000 
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e0)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (10)
'eth0' 
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Seagate   Model: ST380815AS        Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   arm4regs  :   304.000 MB/sec
   8regs     :   215.200 MB/sec
   32regs    :   249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
XFS mounting filesystem sda2
VFS: Mounted root (xfs filesystem).
Freeing init memory: 112K
init started:  BusyBox v1.1.1 (2006.11.29-02:37+0000) multi-call binary
Starting pid 223, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (hddroot) ---
===== Starting checkroot.sh =====
grep: /proc/mtd: No such file or directory
grep: /proc/mtd: No such file or directory
grep: /proc/mtd: No such file or directory
chown: unknown group name: rpcuser
grep: /proc/buffalo/firmware: No such file or directory
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]

===== Starting MountSystemFolders =====
[Success]

Setting up swapspace version 1, size = 139825152 bytes
Adding 136544k swap on /dev/sda3.  Priority:-1 extents:1

===== Starting Kevent.sh =====
[Success]

===== Starting mount_share.sh =====
Mounting /dev/sda4 on /home as a xfs file system.
XFS mounting filesystem sda4

Starting XFS recovery on filesystem: sda4 (dev: sda4)

Ending XFS recovery on filesystem: sda4 (dev: sda4)

Success.

Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
mount: mount point /mnt/mtd does not exist
Failed.
[Failed ]

===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]

===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP  tout=30[s]
eth0: link down

eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>

hostname is setted to KUROBOX-PRO
[Success]

===== Starting smb.sh =====
$Starting SMB services: 
$Starting NMB services: 
[Success]

===== Starting FanController.sh =====
[Success]

===== Starting bootcomplete.sh =====
[Success]


Starting pid 613, console /dev/ttyS0: '/sbin/getty'

KUROUTOSHIKOU KUROBOX Series 

KUROBOX-PRO login: