「(標準Linux)起動メッセージ」の編集履歴(バックアップ)一覧はこちら
「(標準Linux)起動メッセージ」(2008/02/05 (火) 08:55:22) の最新版変更点
追加された行は緑色になります。
削除された行は赤色になります。
#contents()
*起動メッセージ
Orion1 CPU = Low
=== KURO U-Boot. ===
** LOADER **
** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
<<system_bootend>>
Hit any key to stop autoboot: 3 2 1 0
Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
config_device_cs Error : Unknown board
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ff800000, size 8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (10)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Vendor: Seagate Model: ST380815AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
Debug nand_scan : mtd->oobblock=0x00000800
Debug nand_scan : mtd->oobsize=0x00000040
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 215.200 MB/sec
32regs : 249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 112K
--- rcStart (NANDroot) ---
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
mouting usbfs ... [Success]
remouting rootfs ... [Success]
mounting all devices ... [Success]
===== Starting checkroot.sh =====
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]
===== Starting Kevent.sh =====
[Success]
&bold(){HDD未フォーマットの場合}
===== Starting mount_share.sh =====
Mounting /dev/sda on /mnt/disk1 as a xfs file system.
XFS: bad magic number
XFS: SB validate failed
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/sda on /mnt/disk1 as a ext3 file system.
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
&bold(){HDDをフォーマットしている場合}
===== Starting mount_share.sh =====
Mounting /dev/sda1 on /mnt/disk1 as a xfs file system.
XFS mounting filesystem sda1
Starting XFS recovery on filesystem: sda1 (dev: sda1)
Ending XFS recovery on filesystem: sda1 (dev: sda1)
Success.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]
&bold(){LANに未接続の場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
** dhcp fail
** setting default ip
route: SIOC[ADD|DEL]RT: No such process
/etc/dhcpc/dhcpcd.exe ::: down
dhcpcd.exe: interface eth0 has been brought down
add default if
hostname is setted to KUROBOX-PRO
[Success]
&bold(){LANに接続されている場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.9
hostname is setted to KUROBOX-PRO
[Success]
===== Starting httpd.sh =====
[Success]
===== Starting telnet.sh =====
[Success]
===== Starting inetd.sh =====
[Success]
===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]
===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
[Success]
===== Starting bootcomplete.sh =====
[Success]
===== Starting FanController.sh =====
[Success]
===== Starting boss.sh =====
(サングラス男AA)
[Success]
KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:
*メッセージを読む
**電源ON
玄箱PROの電源を入れると、まずCPUのプログラムカウンタにU-Bootのメモリアドレスが設定されU-Bootが実行される。
Orion1 CPU = Low
=== KURO U-Boot. ===
** LOADER **
** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
**周辺装置の初期化
U-Bootによる低レベルでの初期化を行い、カーネルイメージを見つける。
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
<<system_bootend>>
Hit any key to stop autoboot: 3 2 1 0
**メインメモリ上にカーネルを読み込む
見つけたカーネルイメージをメインメモリへ読み込む。
NANDフラッシュの0x20000番地(mtd1の128k以降)からロードする。
Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
<<stop_sound>>
カーネルイメージをメインメモリの0x00100000番地へロード。
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
**カーネルの起動
読み込んだカーネルを実行する。
この時点でU-Bootからカーネルに制御が移される。
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
カーネルが圧縮された自身の展開。
Uncompressing Linux................................................................................................................. done, booting the kernel.
カーネルの起動。
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
config_device_cs Error : Unknown board
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ff800000, size 8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (10)
'eth0'
***SATAデバイスドライバの読み込み
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Vendor: Seagate Model: ST380815AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
***NORフラッシュ
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
***NANDフラッシュ
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
erasesizeとはNANDフラッシュの内容を消去する単位の大きさであり、それが0x00020000、つまり128KBだとなっている。
消去はブロック単位で行われるため、1ブロック128KBだということになる。
Debug nand_scan : mtd->oobblock=0x00000800
OOBとはOut Of Bandの略で、ECCと呼ばれるエラー訂正コードを格納する領域を意味する。
16進数で00000800は10進数で2048を意味し、これはOOBのブロック数を指している。
Debug nand_scan : mtd->oobsize=0x00000040
OOBのサイズが00000040だと意味する。
10進数で64となり、OOBのサイズは64バイトだとわかる。
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
***USB
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 215.200 MB/sec
32regs : 249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
***ネットワーク
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
**rootfsのマウント
ルートファイルシステムのマウント。
bootargs_rootで設定されたデバイスがマウントされている。
VFS: Mounted root (jffs2 filesystem).
initで使用したメモリの解放。
Freeing init memory: 112K
**ルートファイルシステムによる初期化
/etc/init.d/[[rcS]]の実行。
ここからは実際にマウントされたルートファイルシステムによるシステムの初期化。
--- rcStart (NANDroot) ---
***MountSystemFolders関数
/etc/init.d/[[rcS]]内のMountSystemFolders関数の実行。
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
mouting usbfs ... [Success]
remouting rootfs ... [Success]
mounting all devices ... [Success]
***checkroot.sh
/etc/init.d/checkroot.shの実行。
===== Starting checkroot.sh =====
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]
***Kevent.sh
/etc/init.d/[[Kevent.sh]]の実行。
===== Starting Kevent.sh =====
[Success]
***mount_share.sh
/etc/init.d/mount_share.shの実行。
&bold(){HDDが未フォーマットの場合}
===== Starting mount_share.sh =====
Mounting /dev/sda on /mnt/disk1 as a xfs file system.
XFS: bad magic number
XFS: SB validate failed
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/sda on /mnt/disk1 as a ext3 file system.
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
&bold(){HDDがフォーマット済みの場合}
===== Starting mount_share.sh =====
Mounting /dev/sda1 on /mnt/disk1 as a xfs file system.
XFS mounting filesystem sda1
Starting XFS recovery on filesystem: sda1 (dev: sda1)
Ending XFS recovery on filesystem: sda1 (dev: sda1)
Success.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
***sethostname.sh
/etc/init.d/[[sethostname.sh]]の実行。
===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]
***networking.sh
/etc/init.d/[[networking.sh]]の実行。
&bold(){LANに未接続の場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
** dhcp fail
** setting default ip
route: SIOC[ADD|DEL]RT: No such process
/etc/dhcpc/dhcpcd.exe ::: down
dhcpcd.exe: interface eth0 has been brought down
add default if
hostname is setted to KUROBOX-PRO
[Success]
&bold(){LANに接続済みの場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.9
hostname is setted to KUROBOX-PRO
[Success]
***httpd.sh
/etc/init.d/[[httpd.sh]]の実行。
===== Starting httpd.sh =====
[Success]
***telnet.sh
/etc/init.d/[[telnet.sh]]の実行。
===== Starting telnet.sh =====
[Success]
***inetd.sh
/etc/init.d/[[inetd.sh]]の実行。
===== Starting inetd.sh =====
[Success]
***smb.sh
/etc/init.d/[[smb.sh]]の実行。
===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]
***clientUtil_servd.sh
/etc/init.d/[[clientUtil_servd.sh]]の実行。
===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
[Success]
***bootcomplete.sh
/etc/init.d/[[bootcomplete.sh]]の実行。
===== Starting bootcomplete.sh =====
[Success]
***FanController.sh
/etc/init.d/[[FanController.sh]]の実行。
===== Starting FanController.sh =====
[Success]
***boss.sh
/etc/init.d/[[boss.sh]]の実行。
===== Starting boss.sh =====
(サングラス男AA)
[Success]
KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:
----
#contents()
*起動メッセージ
Orion1 CPU = Low
=== KURO U-Boot. ===
** LOADER **
** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
<<system_bootend>>
Hit any key to stop autoboot: 3 2 1 0
Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
config_device_cs Error : Unknown board
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ff800000, size 8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (10)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Vendor: Seagate Model: ST380815AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
Debug nand_scan : mtd->oobblock=0x00000800
Debug nand_scan : mtd->oobsize=0x00000040
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 215.200 MB/sec
32regs : 249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 112K
--- rcStart (NANDroot) ---
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
mouting usbfs ... [Success]
remouting rootfs ... [Success]
mounting all devices ... [Success]
===== Starting checkroot.sh =====
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]
===== Starting Kevent.sh =====
[Success]
&bold(){HDD未フォーマットの場合}
===== Starting mount_share.sh =====
Mounting /dev/sda on /mnt/disk1 as a xfs file system.
XFS: bad magic number
XFS: SB validate failed
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/sda on /mnt/disk1 as a ext3 file system.
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
&bold(){HDDをフォーマットしている場合}
===== Starting mount_share.sh =====
Mounting /dev/sda1 on /mnt/disk1 as a xfs file system.
XFS mounting filesystem sda1
Starting XFS recovery on filesystem: sda1 (dev: sda1)
Ending XFS recovery on filesystem: sda1 (dev: sda1)
Success.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]
&bold(){LANに未接続の場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
** dhcp fail
** setting default ip
route: SIOC[ADD|DEL]RT: No such process
/etc/dhcpc/dhcpcd.exe ::: down
dhcpcd.exe: interface eth0 has been brought down
add default if
hostname is setted to KUROBOX-PRO
[Success]
&bold(){LANに接続されている場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.9
hostname is setted to KUROBOX-PRO
[Success]
===== Starting httpd.sh =====
[Success]
===== Starting telnet.sh =====
[Success]
===== Starting inetd.sh =====
[Success]
===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]
===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
[Success]
===== Starting bootcomplete.sh =====
[Success]
===== Starting FanController.sh =====
[Success]
===== Starting boss.sh =====
(サングラス男AA)
[Success]
KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:
*メッセージを読む
**電源ON
玄箱PROの電源を入れると、まずCPUのプログラムカウンタにU-Bootのメモリアドレスが設定されU-Bootが実行される。
Orion1 CPU = Low
=== KURO U-Boot. ===
** LOADER **
** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
**周辺装置の初期化
U-Bootによる低レベルでの初期化を行い、カーネルイメージを見つける。
PCで言うBIOSのような働きをする。
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 2 1 0
<<system_bootend>>
Hit any key to stop autoboot: 3 2 1 0
**メインメモリ上にカーネルを読み込む
見つけたカーネルイメージをメインメモリへ読み込む。
PCで言うブートローダーの働きをする。
NANDフラッシュの0x20000番地(mtd1の128k以降)からロードする。
Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
<<stop_sound>>
カーネルイメージをメインメモリの0x00100000番地へロード。
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
**カーネルの起動
読み込んだカーネルを実行する。
この時点でU-Bootからカーネルに制御が移される。
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
カーネルが圧縮された自身の展開。
Uncompressing Linux................................................................................................................. done, booting the kernel.
カーネルの起動。
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
config_device_cs Error : Unknown board
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ff800000, size 8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (10)
'eth0'
***SATAデバイスドライバの読み込み
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Vendor: Seagate Model: ST380815AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
***NORフラッシュ
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
***NANDフラッシュ
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
erasesizeとはNANDフラッシュの内容を消去する単位の大きさであり、それが0x00020000、つまり128KBだとなっている。
消去はブロック単位で行われるため、1ブロック128KBだということになる。
Debug nand_scan : mtd->oobblock=0x00000800
OOBとはOut Of Bandの略で、ECCと呼ばれるエラー訂正コードを格納する領域を意味する。
16進数で00000800は10進数で2048を意味し、これはOOBのブロック数を指している。
Debug nand_scan : mtd->oobsize=0x00000040
OOBのサイズが00000040だと意味する。
10進数で64となり、OOBのサイズは64バイトだとわかる。
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
***USB
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 215.200 MB/sec
32regs : 249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
***ネットワーク
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
**rootfsのマウント
ルートファイルシステムのマウント。
bootargs_rootで設定されたデバイスがマウントされている。
VFS: Mounted root (jffs2 filesystem).
initで使用したメモリの解放。
Freeing init memory: 112K
**ルートファイルシステムによる初期化
/etc/init.d/[[rcS]]の実行。
ここからは実際にマウントされたルートファイルシステムによるシステムの初期化。
--- rcStart (NANDroot) ---
***MountSystemFolders関数
/etc/init.d/[[rcS]]内のMountSystemFolders関数の実行。
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
mouting usbfs ... [Success]
remouting rootfs ... [Success]
mounting all devices ... [Success]
***checkroot.sh
/etc/init.d/checkroot.shの実行。
===== Starting checkroot.sh =====
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]
***Kevent.sh
/etc/init.d/[[Kevent.sh]]の実行。
===== Starting Kevent.sh =====
[Success]
***mount_share.sh
/etc/init.d/mount_share.shの実行。
&bold(){HDDが未フォーマットの場合}
===== Starting mount_share.sh =====
Mounting /dev/sda on /mnt/disk1 as a xfs file system.
XFS: bad magic number
XFS: SB validate failed
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/sda on /mnt/disk1 as a ext3 file system.
mount: Mounting /dev/sda on /mnt/disk1 failed: Invalid argument
Failed.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
&bold(){HDDがフォーマット済みの場合}
===== Starting mount_share.sh =====
Mounting /dev/sda1 on /mnt/disk1 as a xfs file system.
XFS mounting filesystem sda1
Starting XFS recovery on filesystem: sda1 (dev: sda1)
Ending XFS recovery on filesystem: sda1 (dev: sda1)
Success.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
***sethostname.sh
/etc/init.d/[[sethostname.sh]]の実行。
===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]
***networking.sh
/etc/init.d/[[networking.sh]]の実行。
&bold(){LANに未接続の場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
** dhcp fail
** setting default ip
route: SIOC[ADD|DEL]RT: No such process
/etc/dhcpc/dhcpcd.exe ::: down
dhcpcd.exe: interface eth0 has been brought down
add default if
hostname is setted to KUROBOX-PRO
[Success]
&bold(){LANに接続済みの場合}
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.9
hostname is setted to KUROBOX-PRO
[Success]
***httpd.sh
/etc/init.d/[[httpd.sh]]の実行。
===== Starting httpd.sh =====
[Success]
***telnet.sh
/etc/init.d/[[telnet.sh]]の実行。
===== Starting telnet.sh =====
[Success]
***inetd.sh
/etc/init.d/[[inetd.sh]]の実行。
===== Starting inetd.sh =====
[Success]
***smb.sh
/etc/init.d/[[smb.sh]]の実行。
===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]
***clientUtil_servd.sh
/etc/init.d/[[clientUtil_servd.sh]]の実行。
===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
[Success]
***bootcomplete.sh
/etc/init.d/[[bootcomplete.sh]]の実行。
===== Starting bootcomplete.sh =====
[Success]
***FanController.sh
/etc/init.d/[[FanController.sh]]の実行。
===== Starting FanController.sh =====
[Success]
***boss.sh
/etc/init.d/[[boss.sh]]の実行。
===== Starting boss.sh =====
(サングラス男AA)
[Success]
KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:
----
表示オプション
横に並べて表示:
変化行の前後のみ表示: